Journal of Welding Science and Technology of Iran
نشریه علوم و فناوری جوشکاری ایران
JWSTI
Engineering & Technology
http://jwsti.iut.ac.ir
1
admin
2476-583X
2676-6787
fa
jalali
1398
6
1
gregorian
2019
9
1
5
1
online
1
fulltext
other
تأثیر آخالها بر تشکیل فریت سوزنی شکل در جوشکاری زیرپودری فولاد کم آلیاژی API5L-X65
Effect of Inclusions on Acicular Ferrite Formation in Submerged Arc Welding of API5L-X65
تخصصي
Special
پژوهشي
Research
در پژوهش حاضر اثر تغییر مشخصه های آخالهای بوجود آمده در جوشکاری زیرپودری فولاد کم آلیاژی API5l-X65، برتشکیل فریت سوزنی شکل مورد بررسی قرار گرفته است. به منظور ایجاد آخالهایی با مشخصه های متفاوت نظیر ترکیب شیمیایی و اندازه آخال، از سه نوع پودر جوشکاری با ترکیب شیمیایی متفاوت و اندیس بازیسیته¬های 72/0، 82/0 و 99/0 و دو حرارت ورودی مختلف kJ/mm 6/1 و kJ/mm 4/2 در جوشکاری بهره برده شده است. نتایج حاصل بیانگر این امر است که عملکرد آخالها به عنوان مکانهای مرجح جوانه زنی فریت سوزنی شکل و بهبود ریزساختار و در نتیجه خواص مکانیکی در شرایطی قابل مشاهده است که پودر مورد استفاده دارای کمترین اندیس بازیسیته بوده و حرارت ورودی بالاتر باشد. تحت این شرایط درصد آخالهای با میزان اکسید تیتانیم بالا و با اندازه 5/0 تا 5/1 میکرومتر افزایش یافته و باعث افزایش میزان فریت سوزنی شکل در ریزساختار می شود. در صورتیکه در بقیه شرایط جوشکاری بوجود آمدن فریت مرزدانه ای سبب کاهش میزان فریت سوزنی شکل شده و سبب تضعیف خواص مکانیکی فلز جوش در مقایسه با فلز پایه می شود.
In the present study, effect of inclusions characteristics changing on the formation of acicular ferrite in submerged arc welding of API5l-X65 low alloy steel was investigated. Three different welding fluxes with different chemical composition and basicity index of 0.72, 0.82 and 0.99, and two different welding heat inputs of 1.6 kJ / mm and 2.4 kJ / mm were used to create inclusions with different characteristics such as chemical composition and size. The results indicate that inclusions acting as acicular ferrite nucleation sites and improvement of the microstructure and resulted mechanical properties, can be observed in welding conditions in which the welding flux with lowest basicity index and higher welding heat input. Under these conditions, the percentage of inclusions with a high titanium oxide value and size range of 0.5 to 1.5 micrometers is increased, which increases the amount of acicular ferrite in the microstructure. However, in other welding conditions, formation of grain boundary ferrite reduces amount of acicular ferrite and weakens mechanical properties of weld metal compared to the base metal<strong><span dir="RTL">.</span></strong>
فریت سوزنی شکل, آخال, جوشکاری زیرپودری, فولاد کم آلیاژی
Acicular Ferrite, Inclusions, Submerged Arc Welding, Low Alloy Steel
77
91
http://jwsti.iut.ac.ir/browse.php?a_code=A-10-84-5&slc_lang=other&sid=1
J. M.
Milani
جواد
ملائی میلانی
10031947532846001558
10031947532846001558
Yes
Faculty of Materials Engineering, Sahand University of Technology, Sahand, Iran
دانشکده مهندسی مواد، دانشگاه صنعتی سهند
T.
Saeid
توحید
سعید
10031947532846001559
10031947532846001559
No
Faculty of Materials Engineering, Sahand University of Technology, Sahand, Iran
دانشکده مهندسی مواد، دانشگاه صنعتی سهند