Journal of Welding Science and Technology of Iran
نشریه علوم و فناوری جوشکاری ایران
JWSTI
Engineering & Technology
http://jwsti.iut.ac.ir
1
admin
2476-583X
2676-6787
fa
jalali
1398
10
1
gregorian
2020
1
1
5
2
online
1
fulltext
fa
بررسی خواص مکانیکی و ریز ساختاری آلیاژ AZ31 جوشکاری شده به روش TIG و TIG پالسی
Evolution of microstructures and mechanical properties of AZ31 magnesium alloy weldment with TIG and Pulsed TIG process
تخصصي
Special
پژوهشي
Research
آلیاژهای منیزیم به دلیل داشتن خواصی مانند استحکام ویژه مناسب، وزن کم و خواص مکانیکی مطلوب کاربردهای زیادی را به خود اختصاص داده­اند. آلیاژ <span dir="LTR">AZ31</span> از نظر جوش پذیری نسبت به سایر آلیاژهای منیزیم وضعیت مناسب­تری دارد بنابراین کاربرد بیشتری نسبت به سایر آلیاژهای منیزیم دارد. در این بررسی از روش جوشکاری <span dir="LTR">TIG</span> و <span dir="LTR">TIG</span> پالسی به منظور جوشکاری و اتصال آلیاژ <span dir="LTR">AZ31</span> استفاده شد و در نهایت ریزساختار و خواص مکانیکی نمونه ها توسط میکروسکوپ نوری، میکروسکوپ الکترونی روبشی(<span dir="LTR">SEM</span>)، آزمون کشش و میکروسختی سنجی مورد بررسی قرار گرفتند. نتایج نشان داد که در ناحیه جوش رسوبات <span dir="LTR">β-Mg<sub>17</sub>Al<sub>12</sub></span> تشکیل شده است و گرمای ورودی اندازه دانه­ها را تحت تاثیر قرار داده و منجر به تغییر در خواص مکانیکی شده است. نمونه جوشکاری به روش <span dir="LTR">TIG</span> با جریان <span dir="LTR">A</span>50 و فرکانس <span dir="LTR">Hz</span>60 بیشترین استحکام(<span dir="LTR">MPa</span>226) را در میان نمونه­های جوشکاری شده به روش <span dir="LTR">TIG</span> و <span dir="LTR">TIG</span> پالسی دارد. در میان نمونه­های جوشکاری شده به روش <span dir="LTR">TIG</span> پالسی نمونه جریان پیک <span dir="LTR">A</span>75 و جریان زمینه <span dir="LTR">A</span>35 بیشترین استحکام(<span dir="LTR">MPa</span>109) را دارد.
Magnesium alloys are very attractive materials owing to their properties of low density, high specific strength and stiffness, good castability, and weldability. AZ31 magnesium alloys in terms of weldability has better situation than the other, so it has more applications than other magnesium alloys. In this study, TIG and pulsed TIG welding method was used to welding the AZ31 alloy and finally microstructure and mechanical properties of welds with metallography, scanning electron microscopy (SEM), tensile test were examined. The results showed that the heat input affected the size of grains that are leading to changes in mechanical properties. Sample was welded with TIG welding with minimum current has maximum strength among the samples both pulsed TIG welding and TIG method. It is observed that with increasing frequency in TIG welding, strength is reduced. Despite the same I<sub>P</sub> and I<sub>B</sub>, higher frequency has created a stronger welding. Also increases the frequency leads to more fine-grained samples, resulting in increased strength.
آلیاژ منیزیم AZ31, جوشکاری قوس تنگستن تحت پوشش گاز محافظ (TIG), خواص مکانیکی.
AZ31 magnesium alloy, TIG, Mechanical properties
89
102
http://jwsti.iut.ac.ir/browse.php?a_code=A-10-239-2&slc_lang=fa&sid=1
Seyedeh Zahra
Anvari
سیده زهرا
انوری
szaanvari@gmail.com
1129624903
10031947532846001848
Yes
PNU
دانشگاه پیام نور
Mohammad Reza
Elahi
محمد رضا
الهی
m.elahi69@yahoo.com
10031947532846001849
10031947532846001849
No
Daneshpajoohan
دانش پژوهان