Journal of Welding Science and Technology of Iran
نشریه علوم و فناوری جوشکاری ایران
JWSTI
Engineering & Technology
http://jwsti.iut.ac.ir
1
admin
2476-583X
2676-6787
fa
jalali
1398
10
1
gregorian
2020
1
1
5
2
online
1
fulltext
fa
بررسی اتصال فاز مایع گذرا فولاد زنگ نزن AISI 304L با ریزساختارهای آستنیتی و مارتنزیتی
Transient liquid phase bonding of AISI 304L stainless steels with the austenitic and martensitic microstructures
تخصصي
Special
پژوهشي
Research
<p dir="RTL">در این پژوهش به بررسی تاثیر زمان و ساختار فلز پایه بر ریزساختار منطقه اتصال فاز مایع گذرای فولاد زنگ نزن <span dir="LTR">L</span>304 پرداخته شده است. اتصال فاز مایع گذرا در دمای <span dir="LTR">°</span><span dir="LTR">C</span>1050 در دو زمان 5 و 60 دقیقه بر روی فلزات پایه با دو ساختار آستنیت درشت دانه و مارتنزیتی و با لایه واسط <span dir="LTR">BNi-2</span> انجام گرفت. جهت ایجاد ساختار تمام مارتنزیتی، نمونه های فولاد زنگ نزن <span dir="LTR">L</span> 304 اولیه در دمای <span dir="LTR">°</span><span dir="LTR">C</span>15- تا 80% نورد سرد شد. بررسی های میکروسکوپی نشان داد که در زمان 5 دقیقه، در ناحیه اتصال دو منطقه انجماد همدما و انجماد غیرهمدما به وجود آمده است. ناحیه انجماد همدما دارای ساختار تکفاز <span dir="LTR">γ</span> و منطقه انجماد غیرهمدما دارای ساختار چندفازی پیچیده ای بود. این در حالی است که پس از 60 دقیقه، تمام ساختار اتصال به صورت همدما انجماد یافته بود و اتصالاتی عاری از عیب حاصل شد. نتایج همچنین نشان داد که ساختار مارتنزیتی فلز پایه که البته در حین سیکل حرارتی جوشکاری به آستنیت فوق ریزدانه بازگشت می یابد تاثیر قابل ملاحظه ای بر عرض ناحیه متاثر از نفوذ داشته است.</p>
In the present study, the effect of time and base metal microstructure on the Transient Liquid Phase (TLP) bonding of 304L stainless steel was studied. TLP was performed at 1050 <sup>0</sup>C for 5 and 60 minutes on the coarse grain austenitic and martensitic microstructure using BNi-2 interlayer. To prepare martensitic microstructure, as-received 304L was rolled at -15 <sup>0</sup>C up to 80% rolling reduction. TEM analysis was proved that the microstructure of 80% rolled samples consisted of two different morphologies of martensite namely as lath-type and dislocation cell type martensite. It was observed that the structure of bonded zone after 5 min has consisted of isothermally solidified zone (ISZ) containing γ solid solution and athermally solidified zone (ASZ) containing complex boride phases. Meanwhile, after 60 min of heating, the structure of bonded zone completely solidifies isothermally. The obtained results also showed that the martensitic microstructure considerably effect on the width of diffusion affected zone (DAZ) which was related to the reversion of martensite to ultrafine grain austenite during heating.
فولاد زنگ نزن304L, اتصال فاز مایع گذرا, نفوذ, انجماد همدما, ناحیه متاثر از نفوذ.
AISI 304L stainless steel, Transient liquid phase bonding, Diffusion, Isothermal solidification, Diffusion affected zone.
1
11
http://jwsti.iut.ac.ir/browse.php?a_code=A-10-140-1&slc_lang=fa&sid=1
S.
Ghaderi
سینا
قادری
10031947532846001831
10031947532846001831
No
دانشکده مهندسی مواد، دانشگاه صنعتی اصفهان.
F.
Karimzadeh
فتح اله
کریم زاده
10031947532846001832
10031947532846001832
Yes
دانشکده مهندسی مواد، دانشگاه صنعتی اصفهان.
A.
Ashrafi
علی
اشرفی
10031947532846001833
10031947532846001833
No
دانشکده مهندسی مواد، دانشگاه صنعتی اصفهان.